- 您现在的位置：买卖IC网 > Sheet目录652 > 50212L (Switchcraft Inc.)SWITCH SLIDE 4PDT LOCKING
EN3 MINIWEATHERTIGHTCONNECTORSERIES
42
CONNECTORS & RECEPTACLES
?
PHONE: 773 792-2700
* Please visit the product pages on our website for the most up-to-date product information
CRIMP CONTACT
CRIMP TOOLS
INSERTION INSTRUCTIONS
Part Number
EN3INS16
EN3INS20
EN3CR
EN3CRAUTO
EN3POS16
EN3POS20
Tool Description
Insertion/Extraction Tool for 16 AWG
Insertion/Extraction Tool for 20 AWG
Crimp Hand Tool
Pneumatic Crimp Tool
Positioner for 16 AWG contacts and pins
Positioner for 20 AWG contacts and pins
CRIMP CONTACT
EXTRACTION INSTRUCTIONS
NOTE: A positioner must be used with the
EN3CR and EN3CRAUTO.
Note: Solder and PC contacts are factory assembled
CORD CONNECTOR ASSEMBLY INSTRUCTIONS
STEP 1
Cord Connector: To assemble the three-part cord connector, first feed the end of the cable through the boot, cable clamp
housing, and coupling ring in that order and position as shown in the figure below. NOTE: The coupling ring can also be
inserted onto the cord connector from the front. In-line Connector: Feed the end of the cable through the boot and cable
clamp housing in the order and position shown.
IN-LINE
CABLE
BOOT
COUPLING
RING
CORD
CONNECTOR
CABLE
BOOT
CABLE CLAMP
HOUSING
CONNECTOR
CABLE CLAMP
HOUSING
CONTACT PINS
O-RING
(MOLDED ONTO
CONTACT PINS
CORD CONNECTOR)
STEP 2
Next, strip the cable .218" as shown and begin soldering conductors to pins, or insert contacts crimped on wire starting
with contact #1 next to the "notch" and following with the remaining conductors counter-clockwise with #6 or #8 conductor
in the center.
3/8"
MAX.
7/32"
SOLDER
NOTCH (PIN #1
INDICATOR)
CORD
CONNECTOR
9/32"
3/8"
MAX.
7/32"
SOLDER
NOTCH (PIN #1
INDICATOR)
IN-LINE
CONNECTOR
9/32"
STEP 3
Push the cable clamp housing forward until it locks
into the connector body and snap the two clamps
into their compartments.
CORD CONNECTOR
CABLE CLAMPS
IN-LINE CONNECTOR
CABLE CLAMPS
STEP 4
CORD CONNECTOR
IN-LINE CONNECTOR
Finally, push the boot all the way forward to seat tightly
onto the cable clamp housing.
Remember: Cord connectors will not mate with each other. For cord-to-cord connection,
your customer must order a cord connector plus an in-line connector.
DIMENSIONS ARE FOR REFERENCE ONLY
Inch
(mm)
www.switchcraft.com
? Registered trademark of Switchcraft, Inc.
Note: Contact your Switchcraft Representative for price and delivery
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
5026N-36
BANTAM PLUG/2 ALLIGATOR CLIP 36"
50475C
CHOKE COMMON MODE 4.7MH 0.4A SMD
5051
BNC FEMALE TO #8 SPADE LUGS
5053-60-2
MICROGRABBER/BANANA PLUG 60" RED
505
DIGITAL PHOTO/CONTACT TACHOMETER
5069
BNC FEMALE-.025" PIN RECEPT 7"
50J1066
WASHER NON-TURN 1/8"
50J5092
STOP PIN FOR 50 AND 51 SERIES
相关代理商/技术参数
50212LX
功能描述:滑动开关 4PDT SLIDE SWITCH
RoHS:否 制造商:C&K Components 触点形式:SPDT 开关功能:Momentary 触点额定值: 端接类型: 执行器:Extended, Side 安装风格:SMD/SMT 触点电镀:Silver 封装:
5021-2P
功能描述:工业控制变压器 240V 0-240/0-280Vout 120Vin 0-280Vout 56A
RoHS:否 制造商:Sola/Hevi-Duty 功率额定值: 初级电压额定值:120 V to 240 V 次级电压额定值:24 V 安装风格:Chassis 一次绕组:Dual Primary Winding 二次绕组:Single Secondary Winding 长度:3.89 in 宽度:4.5 in 高度:4.48 in
5021-2S
功能描述:工业控制变压器 480V 0-480/0-560Vout 240Vin 0-560Vout 28A
RoHS:否 制造商:Sola/Hevi-Duty 功率额定值: 初级电压额定值:120 V to 240 V 次级电压额定值:24 V 安装风格:Chassis 一次绕组:Dual Primary Winding 二次绕组:Single Secondary Winding 长度:3.89 in 宽度:4.5 in 高度:4.48 in
50213001J
制造商:TEKTRONIX INC. 功能描述:
50-2-13001J
制造商: 功能描述: 制造商:undefined 功能描述:
502134
功能描述:手工工具 Wire-Wrap 24 AWG Bit Std 3.30" x .45"
RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool
502134-1
功能描述:光纤连接器 OVEN CURING ASSY W/ADAPTER BLOCK RoHS:否 制造商:Molex 产品:Adapters 类型:8 Port with External Shutter 连接器类型:Adapter 模式:Multimode 光纤直径: 颜色:Blue 附件类型:LC Adapter
502134-2
功能描述:光纤连接器 OVEN ASSY, HEAT CURE, OPT. RoHS:否 制造商:Molex 产品:Adapters 类型:8 Port with External Shutter 连接器类型:Adapter 模式:Multimode 光纤直径: 颜色:Blue 附件类型:LC Adapter